Reinitialize your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may need to reinitialize your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the configurations or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a easy process that can be performed in just a few actions.

• Initially ensuring your red dot sight is activated.
• Identify the small reinitialize button on the bottom of the unit.
• Use a thin tool to activate the reset lever for approximately 7 moments.
• Let go the reset button and your Holosun EPS Carry Red Dot sight will restart.
• Its red dot sight should now be set back to its factory settings.

Restore Your Holosun EPS Carry Red Dot to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to go back to basics, resetting it to default configuration is a breeze. First, determine the tiny button on the side of your optic. Then, sustain it for around ten seconds until you see the indicator light change. Your Holosun EPS Carry is now reverted to its factory settings, ready for consistent targeting.

Bring Your Holosun EPS Carry Back to Life

Is your beloved Holosun EPS Carry experiencing some performance problems? Don't despair! A simple factory reset can often fix the problem and get your red dot sight back to its former glory. Before you begin, remember to remove the battery from your Holosun EPS Carry to prevent accidental activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these straightforward steps:

• Simultaneously press and hold the power button for approximately 5 seconds.
• The display will flash, indicating that the reset is being performed.
• Let go of the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can connect the battery and test your sight's functionality. If you encounter any further problems, don't hesitate to reach out to their technical assistance.

Return Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Adhere to these steps carefully to ensure a successful factory reset.

• Beginning with, Energize your Holosun EPS Carry by pressing the power button.
• Next, press and hold both the mode button and the up/down adjustment button simultaneously.
• While continue holding these buttons, press the power button once.
• You will show a confirmation prompt indicating that the reset process is initiated.
• Allow the process to complete. This may take a few moments. Once done, your Holosun EPS Carry will automatically shutdown.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Reset All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Holding a specific button combination. Consult your Manual for the exact button sequence for your model. Once in the settings menu, look for an option that says "Clear Settings". Select this option and confirm the reset. Your sight will then power off and restart with all settings Restored to their default values.

Reset your Holosun EPS Carry through a Factory Default Settings

If your Holosun EPS Carry is acting funny, a factory reset might be the solution. This will how to factory reset Holosun EPS Carry red dot return your sight to its factory settings, clearing any personalized configurations you've made. To execute this reset, follow these simple steps:

• Initially, identify the reset switch on your EPS Carry.
• Then, use a thin object, like a toothpick, to depress the reset lever.
• During maintain the reset lever activated, activate your EPS Carry.
• You'll blink a message indicating that the reset is successful.

When the reset is complete, your EPS Carry will be set to its factory settings.

Report this wiki page